GMC Savana 3500 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a GMC Savana 3500 Brake Drum Replacement is $370 with $208 for parts and $161 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1998 GMC Savana 3500V6-4.3L	Service typeBrake Drum Replacement	Estimate$1419.69	Shop/Dealer Price$1684.63 - $2371.45
2007 GMC Savana 3500V8-6.0L	Service typeBrake Drum Replacement	Estimate$604.36	Shop/Dealer Price$732.12 - $1077.05
2004 GMC Savana 3500V8-4.8L	Service typeBrake Drum Replacement	Estimate$647.72	Shop/Dealer Price$786.31 - $1163.77
2000 GMC Savana 3500V8-5.7L	Service typeBrake Drum Replacement	Estimate$1153.17	Shop/Dealer Price$1375.45 - $1934.35
2012 GMC Savana 3500V8-6.6L Turbo Diesel	Service typeBrake Drum Replacement	Estimate$604.36	Shop/Dealer Price$732.14 - $1077.09
2009 GMC Savana 3500V8-4.8L	Service typeBrake Drum Replacement	Estimate$604.36	Shop/Dealer Price$732.11 - $1077.05
2014 GMC Savana 3500V8-4.8L	Service typeBrake Drum Replacement	Estimate$612.86	Shop/Dealer Price$740.38 - $1085.14
2015 GMC Savana 3500V8-6.0L	Service typeBrake Drum Replacement	Estimate$612.86	Shop/Dealer Price$741.02 - $1086.25

Show example GMC Savana 3500 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert GMC mechanics

Real customer reviews from GMC owners like you.

Excellent Rating

(31)

Rating Summary

27

3

0

0

1

27

3

0

0

1

SEE REVIEWS NEAR ME

Dan

39 years of experience

981 reviews

Dan

39 years of experience

by Doug

GMC Savana 3500 V8-6.0L - Shock Absorber Replacement (Front, Rear) - Cumming, Georgia

Dan showed up on time was professional and changed the front shocks as I requested. No complaints whatsoever

Rodric

14 years of experience

414 reviews

Rodric

14 years of experience

by James

GMC Savana 3500 V8-5.7L - Power Steering Pump - Douglasville, Georgia

professional, timely, efficient and personable

Lavell

28 years of experience

244 reviews

Lavell

28 years of experience

by Jack

GMC Savana 3500 V8-6.0L - Car is not starting - San Francisco, California

Lavell arrived early, was very courteous and professional. He took time to explain the situation regarding the issues with my vehicle. His explanation was thorough and actually, reassuring. Very nice experience.

Jim

21 years of experience

31 reviews

Jim

21 years of experience

by Ted

GMC Savana 3500 V8-5.7L - Idle Control Valve - Saint Paul, Minnesota

Truck is running never better Thanks again

Excellent Rating

(31)

Rating Summary

27

3

0

0

1

27

3

0

0

1

SEE REVIEWS NEAR ME

Recent articles & questions

Symptoms of a Bad or Failing Clutch Safety Switch

If your manual car is not starting, starts while in gear, or has the Check Engine Light on, you may need to replace the clutch safety switch.

Symptoms of a Bad or Failing Steering Gear Adjuster Plug

Common signs include the steering wheel feeling loose or hard to turn, leaking power steering fluid, and the steering wheel shaking while driving.

How Much Does a Mechanic Make in Vermont?

Automotive technician jobs in Vermont have an average mechanic salary of $37k, with some mechanics earning a salary of $53k.

What is the satellite radio electronic serial number on the SIRIUS Radio and why is it necessary?

Your SIRIUS Radio is equipped with a unique identifying number, called the satellite radio electronic serial number, or ESN. The ESN is used to identify your radio when applying for SIRIUS Radio service. It’s a 12-digit number and you must...

What makes a car's temperature normal at idle but hot while driving? - 2000 Chevrolet Malibu

This may be related to a few different things, such as a clogged radiator not allowing coolant to circulate properly, a thermostat that may be stuck closed not allowing coolant to flow through the motor, or potentially a bad coolant...

Hard transmission shifting, second time replaced

Hey there. This may be related to a bad or failing transmission control solenoid (https://www.yourmechanic.com/services/downshift-solenoid-replacement) or potentially the control module itself. As you know, the transmission control module has various sensors such as vehicle speed sensors (https://www.yourmechanic.com/services/speed-sensor-replacement), wheel speed sensors...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com