Ford Maverick Control Arm Assembly Replacement Costs

What is a control arm and how does it work?

A control arm is a suspension component, usually made of heavy gauge steel or aluminum, that links the steering knuckle in the front — or axle carrier in the rear — to the frame of the vehicle. Many vehicles have upper and lower control arms. The inboard link(s) of the arm securely bolt to the frame of the vehicle through rubber bushings, while the outboard link of the control arm connects to the steering knuckle through a ball joint; all of which allow the control of the up and down movement of the steering knuckle or axle carrier. This minimizes the transmission of shock and vibration to the vehicle’s body.

When to consider replacing a control arm:

The structural portion of the control arm can last the life of the vehicle — except for cases of corrosion or crash damage. However, the rubber bushings and the ball joint in a control arm have a limited life. A mechanic should investigate if you notice:

Wheel alignment difficulties. Should the bushings, or the ball joint, in a control arm be worn, it will be impossible to properly align the vehicle. The worn components, or the entire arm, must be replaced.
Vehicle won’t track straight or pulls to one side. A car will not track straight and may require constant steering correction if there is a worn, bent, or loose control arm.
Clunking or squeaking noise. A loose control arm, or a control arm with dried out, rotted, or loose bushings, may move enough to cause detectable noise from the suspension as you go over bumps in the road.
Vehicle pulls to one side only when braking. Worn bushings or ball joints can allow control arm to shift when braking, causing the vehicle to pull to one side. Although, this could also be caused by brake calipers.

How do mechanics replace a control arm?

The vehicle is raised and supported on steel jack stands, and the wheel and tire assembly is removed.
Stabilizer bar links are detached from the control arm, if applicable. ABS wiring to the wheel speed sensor, if routed along the arm, is disconnected.
Control arm mounting bolts are detached from the frame and from the axle carrier if the control arm is in the rear.
For front control arms connected to the steering knuckle via a ball joint, the nut is removed from the ball joint stud and the stud is pushed through the steering knuckle to free the arm.
The arm is lowered from the vehicle and examined by the mechanic to confirm that the noise, or other problem, actually originated from a defect in the arm.
The new arm is installed using new mounting bolts if required by the service manual. In many cases, the fasteners must be tightened with the vehicle weight on the suspension in order to ensure the bushings are in a neutral, or resting, position.
The vehicle is lowered and road tested to confirm the problem is resolved. Replacing a control arm will change the vehicle alignment settings and the mechanic will refer you to a professional alignment shop to have the vehicle alignment set to factory specifications.

Is it safe to drive with a control arm problem?

No. If the car wanders on the road, pulls to one side, or noise from the suspension is loud, you need to schedule repair right away. Should the problem be limited to low levels of noise, such as clunking or squeaking, continued use of the car is reasonable until you can schedule a repair. Should the control arms be damaged as a result of a collision, it would be unsafe to drive the car until it is repaired.

When replacing a control arm keep in mind:

The number of control arm types vary from vehicle to vehicle depending on the design of the vehicle suspension.
Control arms should be replaced in pairs — arms on both sides of a front or rear axle — if the reason for replacement is worn control arm bushings or a worn ball joint.
All other suspension components should be inspected when control arms are replaced because looseness, damage, or excessive wear in other parts of the suspension system will make it impossible to perform a wheel alignment after the control arms are replaced.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Ford mechanics

Real customer reviews from Ford owners like you.

Excellent Rating

(134)

Rating Summary

128

SEE REVIEWS NEAR ME

Christian

23 years of experience

68 reviews

Request Christian

by Alfredo

Ford Maverick * - Battery - Hayward, California

Ben

42 years of experience

1589 reviews

Request Ben

by Andrew

Ford F-150 V6-3.5L Turbo - Control Arm Assembly Replacement (Front Lower Left) - Houston, Texas

Friendly, prompt and thorough

Nathan

30 years of experience

260 reviews

Request Nathan

by Cory

Ford F-150 V8-5.4L - Control Arm Assembly Replacement (Front Upper Left, Front Upper Right, Front Lower Left, Front Lower Right) - Tulsa, Oklahoma

Very reliable with giving information and details on diagnoses and suggestions on vehicles. Was punctual and organized and kept me updated as he did his job on my vehicle. Im going to recommend Nathan to everyone... My mechanic is the Future

David

17 years of experience

639 reviews

Request David

by Lisa

Ford Fusion L4-2.5L - Control Arm Assembly Replacement (Front Upper Left, Front Upper Right) - Vacaville, California

Very nice and professional guy

Ford Maverick Control Arm Assembly Replacement at your home or office.

Estimate price near me

Control Arm Assembly Replacement Service

How much does a Control Arm Assembly Replacement cost?

On average, the cost for a Ford Maverick Control Arm Assembly Replacement is $273 with $119 for parts and $154 for labor. Prices may vary depending on your location.

What is a control arm and how does it work?

When to consider replacing a control arm:

How do mechanics replace a control arm?

Is it safe to drive with a control arm problem?

When replacing a control arm keep in mind:

Meet some of our expert Ford mechanics

Excellent Rating

Rating Summary

Christian

Ben

Nathan

David

Excellent Rating

Rating Summary

Recent articles & questions

Belts squeal when starting, turning, and going in reverse.

Horn and brake lights not working

Been having problems with the a/c in my 2006 Mazda 5 sometimes it works and sometimes it don't for the pass 6 days. Today my husb

How can we help?