Ford F-250 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Ford F-250 Brake Drum Replacement is $459 with $231 for parts and $228 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1973 Ford F-250V8-5.0L	Service typeBrake Drum Replacement	Estimate$992.36	Shop/Dealer Price$1195.45 - $1750.74
1972 Ford F-250V8-6.4L	Service typeBrake Drum Replacement	Estimate$691.22	Shop/Dealer Price$831.07 - $1196.54
1993 Ford F-250V8-7.5L	Service typeBrake Drum Replacement	Estimate$985.12	Shop/Dealer Price$1169.61 - $1621.66
1991 Ford F-250V8-7.3L Diesel	Service typeBrake Drum Replacement	Estimate$975.62	Shop/Dealer Price$1159.01 - $1610.24
1962 Ford F-250L6-4.3L	Service typeBrake Drum Replacement	Estimate$690.32	Shop/Dealer Price$829.98 - $1194.80
1981 Ford F-250L6-4.9L	Service typeBrake Drum Replacement	Estimate$984.40	Shop/Dealer Price$1197.54 - $1782.89
1991 Ford F-250V8-5.8L	Service typeBrake Drum Replacement	Estimate$997.62	Shop/Dealer Price$1180.51 - $1631.36
1985 Ford F-250V8-5.0L	Service typeBrake Drum Replacement	Estimate$1026.96	Shop/Dealer Price$1218.83 - $1692.91

Show example Ford F-250 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Ford mechanics

Real customer reviews from Ford owners like you.

Excellent Rating

(123)

Rating Summary

114

4

0

1

4

114

4

0

1

4

SEE REVIEWS NEAR ME

Lucas

21 years of experience

887 reviews

Lucas

21 years of experience

by Thomas

Ford F-250 V8-7.5L - Starter - North Hollywood, California

Great Service and very helpful.

Jay

37 years of experience

953 reviews

Jay

37 years of experience

by FRANK

Ford F-250 V8-7.5L - Car is not starting - Upland, California

Robert

42 years of experience

232 reviews

Robert

42 years of experience

by Harlan

Ford F-250 * - Car is not starting - Tomball, Texas

Sean

17 years of experience

111 reviews

Sean

17 years of experience

by Kenneth

Ford F-250 V8-5.8L - Car starts and then dies - Alexandria, Virginia

Very knowledgable. Quickly diagnosed vehicle issue. Very professional.

Excellent Rating

(123)

Rating Summary

114

4

0

1

4

114

4

0

1

4

SEE REVIEWS NEAR ME

Recent articles & questions

How Long Do Wiring Harnesses Last?

Car wiring harnesses connect all the different electrical systems and components in a vehicle. Wiring harnesses can last the lifetime of the vehicle.

How Do I Tint My Windows?

Tinting Tinting the windows on your car provides several benefits, including: Provides privacy Keeps the car interior cooler Blocks harmful ultraviolet rays Dims the sun’s brightness inside Enhances the car’s appearance Applying window tint may sound easy and is only...

P2522 OBD-II Trouble Code: A/C Request B Circuit

P2522 means a there is a problem from the air conditioning refrigerant pressure sensor which may be caused by low refrigerant in the A/C system.

How to replace interior door handle cable.

Generally, you have to hold the door panel up, pull the handle, and snap the cable in at an angle. Different cars will have different mechanisms, and some may be more difficult than others. If you are still having problems,...

So I just changed my oil in a 2011 dodge charger for the 3rd time the oil pressure is going from 30 to about 80 is this normal

Hi Cassandra. As long as you've used the recommended oil viscosity and correct filter, you should be OK with the range you are describing. It's typical for oil pressure to range anywhere from 25 on the low end to 40...

After change taillight and evaporation purge valve on 06 Cadillac SRX will not crank over or attempt to start key lock in ignitio

Hi Anthony. While we appreciate the question tonight, I'm not sure how we can help in this case. Anytime you install used parts on a vehicle, you're going to risk having compatibility and connectivity issues. If the power was not...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com