Chrysler Town & Country Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Chrysler Town & Country Brake Drum Replacement is $294 with $171 for parts and $123 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1963 Chrysler Town & CountryV8-6.3L	Service typeBrake Drum Replacement	Estimate$673.16	Shop/Dealer Price$796.45 - $1112.34
1967 Chrysler Town & CountryV8-7.2L	Service typeBrake Drum Replacement	Estimate$625.16	Shop/Dealer Price$748.50 - $1064.42
1998 Chrysler Town & CountryV6-3.3L	Service typeBrake Drum Replacement	Estimate$583.32	Shop/Dealer Price$701.69 - $1011.72
2013 Chrysler Town & CountryV6-3.6L	Service typeBrake Drum Replacement	Estimate$557.23	Shop/Dealer Price$677.28 - $1005.95
2001 Chrysler Town & CountryV6-3.8L	Service typeBrake Drum Replacement	Estimate$567.53	Shop/Dealer Price$691.58 - $1034.39
1964 Chrysler Town & CountryV8-6.3L	Service typeBrake Drum Replacement	Estimate$625.16	Shop/Dealer Price$748.49 - $1064.41
2008 Chrysler Town & CountryV6-4.0L	Service typeBrake Drum Replacement	Estimate$626.23	Shop/Dealer Price$761.62 - $1136.68
2002 Chrysler Town & CountryV6-3.8L	Service typeBrake Drum Replacement	Estimate$574.03	Shop/Dealer Price$698.37 - $1041.40

Show example Chrysler Town & Country Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Chrysler mechanics

Real customer reviews from Chrysler owners like you.

Excellent Rating

(891)

Rating Summary

826

36

3

9

17

826

36

3

9

17

SEE REVIEWS NEAR ME

Richard

35 years of experience

8 reviews

Request Richard

Richard

35 years of experience

Request Richard

by Vasilya Verdi

Town & Country 2011 - Oil Cooler - Tampa, FL

Richard is a wizard among the car mechanics. Incredible specialist and a very nice person. He can identify the issue from first sight. In my case, he was the second mechanic. The first one assumed that issue in damaged hoses. When Richard came and look at the vehicle's insides, he immediately figured out that the problem is in the damaged Oil Cooler. And he was right. I ordered the necessary part online, and when it was delivered, I asked YourMechanic to schedule Richard to fix the car. It took him less than 1 hour to replace the part which was hidden under the intake. He de-installed the intake, changed the Oil Cooler, and return everything back. No mess around, no noise - clean, fast and perfect job. I'd say he works as a car surgeon. I highly recommend Richard and wish him all the best.

Kevin

7 years of experience

27 reviews

Kevin

7 years of experience

by Steve duke

Town & Country 2005 - Alternator - Orlando, FL

Very fast and knowledgeable just an outstanding service all around will definitely use the service and recommended kevin

Mike

25 years of experience

79 reviews

Mike

25 years of experience

by Regina Walker

Town & Country 2014 - Loud clicking noise when I turn the car - Romulus, MI

Very professional! On time, went right to work. Explained what was done & what would be needed. Compete clean up of area when he was done.

Mike

25 years of experience

79 reviews

Mike

25 years of experience

by Renita Gray

Town & Country 2004 - Oil Change - Romulus, MI

Mike arrived promptly. He was courteous with great customer service skills. He completed the service in a timely manner and explained what was recommended with a smile behind his ppe. I am very happy with this mechanic and will be using his services in the future!

Excellent Rating

(891)

Rating Summary

826

36

3

9

17

826

36

3

9

17

SEE REVIEWS NEAR ME

Recent articles & questions

How Does My Car Monitor Tire Pressure?

You’re You’re driving home from work and your steering wheel begins to pull. It gradually gets worse, then you hear a thump-thump-thump noise. You stop on the side of the highway to investigate, only to find you’ve got a flat...

What Are the Benefits of Having an Engine Rebuilt Instead of Replaced?

Rebuilding a damaged engine may be a more economical option than full replacement. In an engine rebuild bearings, gaskets, and seals are replaced.

10 Best Car Cell Phone Holders and Mounts

Cell phone holders and phone stands for car dashboards help you safely drive hands-free. Car phone mounts for iPhone and Samsung range from $20-50.

How to fix AC on a '95 Infiniti J30

Those Infinitis are electronic nightmares. All of that AC system is run by the computer. If you jump it and it works, watch my video. I even have a video "how to fix your AC system cheaply (https://www.youtube.com/watch?v=ah4OEeCu1KE)." Just get...

After parts replaced, bubbles in reservoir

Hello. If all of the air is out of the system then the issue is internal. It is typically caused by a blown head gasket. This can occur when the leak is really small. When it is small enough the...

Vehicle turns off at any rpm, at idle or highway speeds, without stumbling or warning.

This kind of a stalling issue can be caused by a variety of problems. They are typically caused by ignition faults, wiring faults, and fuel issues. Although you do not have a Check Engine Light on, you should still scan...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com