Chrysler LHS Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Chrysler LHS Brake Drum Replacement is $307 with $212 for parts and $95 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1994 Chrysler LHSV6-3.5L	Service typeBrake Drum Replacement	Estimate$709.71	Shop/Dealer Price$864.64 - $1302.43
1999 Chrysler LHSV6-3.5L	Service typeBrake Drum Replacement	Estimate$519.23	Shop/Dealer Price$635.31 - $961.00
1995 Chrysler LHSV6-3.5L	Service typeBrake Drum Replacement	Estimate$538.23	Shop/Dealer Price$656.31 - $983.50
2001 Chrysler LHSV6-3.5L	Service typeBrake Drum Replacement	Estimate$519.23	Shop/Dealer Price$635.29 - $960.96
2000 Chrysler LHSV6-3.5L	Service typeBrake Drum Replacement	Estimate$519.23	Shop/Dealer Price$635.32 - $961.03
1997 Chrysler LHSV6-3.5L	Service typeBrake Drum Replacement	Estimate$538.23	Shop/Dealer Price$656.31 - $983.50
1996 Chrysler LHSV6-3.5L	Service typeBrake Drum Replacement	Estimate$544.23	Shop/Dealer Price$662.15 - $989.22

Show example Chrysler LHS Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Chrysler mechanics

Real customer reviews from Chrysler owners like you.

Excellent Rating

(28)

Rating Summary

26

0

1

0

1

26

0

1

0

1

SEE REVIEWS NEAR ME

Don

18 years of experience

63 reviews

Don

18 years of experience

by Marilyn

Chrysler LHS V6-3.5L - Oil/Fluid Leak - Chicago, Illinois

Don was very professional and knowledgeable thank you Don

Berchel

18 years of experience

101 reviews

Request Berchel

Berchel

18 years of experience

Request Berchel

by Ken

Chrysler LHS V6-3.5L - Car is not starting - Towson, Maryland

Prompt, efficient, and knowledgable. Perfect!

Russell

24 years of experience

356 reviews

Request Russell

Russell

24 years of experience

Request Russell

by jon

Chrysler LHS V6-3.5L - Adjust Drive Belts - Portland, Oregon

Russell stopped what he was working on in order to come and put on my serpentine belt in the freezing cold but he was quick and accurate in finding the right way to do the work for me. He showed his skills as a mechanic quickly and fixed my car for me in pretty short order. He was very polite, professional and I will ask for him now whenever I have a problem with my car that I can't fix.

Russell

27 years of experience

271 reviews

Request Russell

Russell

27 years of experience

Request Russell

by Heath

Chrysler LHS V6-3.5L - Battery - Dublin, California

Great!

Excellent Rating

(28)

Rating Summary

26

0

1

0

1

26

0

1

0

1

SEE REVIEWS NEAR ME

Recent articles & questions

The Best Used Cars to Buy for Long Commutes

Most Most of us are faced with the prospect of commuting back and forth to work on a daily basis, but some have a much longer drive than others. When it comes time to buy a car, you need to...

How to Budget to Buy a New Car

Saving money for a new car or a used car (https://www.yourmechanic.com/article/what-are-the-pros-and-cons-of-buying-a-new-or-a-used-vehicle) that’s new to you doesn’t have to be a source of stress. With the proper planning, you can simplify the process without making a huge financial sacrifice all at...

How to Drive a Car in the Mud

While While off-roaders (https://www.yourmechanic.com/article/5-essential-things-to-know-about-off-roading) - equipped with giant 4X4s, tires designed for iffy terrain, and friends with winches to pull them out in times of failure - may actually seek out muddy conditions, it is advisable for those behind the...

Stalled while driving on highway now won't start turns over but won't start

Hello There, Stalling at high speeds as you describe can be related to many different things such as a random electrical failure or potentially a fuel supply issue. Since the truck does turn over and fire, this suggests you are...

clutch pedal goes strait to floor and brake fluid is empty

You've probably had a failure in the clutch slave cylinder. The level in the brake fluid reservoir falls because the clutch also uses fluid from the same reservoir. There are compartments in there so that a leak in clutch system...

I would like to ask about key fobs

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com