Chevrolet C2500 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Chevrolet C2500 Brake Drum Replacement is $710 with $254 for parts and $456 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1997 Chevrolet C2500V8-5.7L	Service typeBrake Drum Replacement	Estimate$1061.03	Shop/Dealer Price$1236.31 - $1654.13
1999 Chevrolet C2500V8-6.5L Turbo Diesel	Service typeBrake Drum Replacement	Estimate$965.03	Shop/Dealer Price$1140.39 - $1558.27
1993 Chevrolet C2500V6-4.3L	Service typeBrake Drum Replacement	Estimate$965.03	Shop/Dealer Price$1140.39 - $1558.26
1991 Chevrolet C2500V8-6.2L Diesel	Service typeBrake Drum Replacement	Estimate$965.03	Shop/Dealer Price$1140.28 - $1558.07
1994 Chevrolet C2500V8-5.0L	Service typeBrake Drum Replacement	Estimate$965.03	Shop/Dealer Price$1140.46 - $1558.39
1988 Chevrolet C2500V8-6.2L Diesel	Service typeBrake Drum Replacement	Estimate$963.17	Shop/Dealer Price$1138.06 - $1554.54
1995 Chevrolet C2500V8-5.0L	Service typeBrake Drum Replacement	Estimate$989.03	Shop/Dealer Price$1163.73 - $1581.12
1994 Chevrolet C2500V8-7.4L	Service typeBrake Drum Replacement	Estimate$989.03	Shop/Dealer Price$1165.52 - $1584.25

Show example Chevrolet C2500 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Chevrolet mechanics

Real customer reviews from Chevrolet owners like you.

Excellent Rating

(32)

Rating Summary

31

1

0

0

0

31

1

0

0

0

SEE REVIEWS NEAR ME

David

25 years of experience

180 reviews

David

25 years of experience

by James

Chevrolet C2500 V8-5.7L - Brake Light Switch - Ocala, Florida

Hi.David was prompt and polite to my mother, b/c I had to be at work while he fixed the brake light switch on my truck. I found it was very convenient that he came to the house to do the repair. The quote for the repair was exactly what I was charged. This is the second time I have used his service and YourMechanic, and would use it again if necessary. James

Kyle

25 years of experience

18 reviews

Kyle

25 years of experience

by Augie

Chevrolet C2500 V8-5.7L - Oil/Fluid Leak - San Ramon, California

diagnosed the problem within 10 minutes and repaired it within 1/2 hr.. Saved me about 250 bucks for a towing job plus repairs.

Scott

36 years of experience

904 reviews

Scott

36 years of experience

by Joel

Chevrolet C2500 V8-5.7L - Front Crankshaft Seal - Chandler, Arizona

Awesome job!!

Chris

18 years of experience

494 reviews

Chris

18 years of experience

by Candido

Chevrolet C2500 V8-5.7L - Distributor Rotor and Cap - Richmond, Texas

Good and reliable .

Excellent Rating

(32)

Rating Summary

31

1

0

0

0

31

1

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

How to Adjust the Rearview Mirror for Nighttime Driving

We’ve We’ve all been there before. You’re driving down the road at night when a car comes up behind you. Because of some trick in height difference or distance from your rear bumper, it feels like their headlights are glaring...

Can I Make My Own Windshield Washer Fluid?

Washer Washer fluid is typically tinted to indicate that it is not safe to consume and, though most commonly blue, it comes in a variety of colors. Warning labels caution that washer fluid contains harmful and poisonous chemicals, including methanol....

How to Transport Your Car Overseas

Whatever the reason, whether for work or retirement, there may come a time when you want to ship (https://www.yourmechanic.com/article/how-to-choose-the-best-car-shipping-company) your vehicle overseas. When arranging for your vehicle to be shipped overseas, there are quite a few options and steps you...

Power window not working.

If the motor is getting power from the switch and still not moving, the problem is the motor / regulator. If no power is received from the switch when pressing, the problem is the switch. Make sure the fuse is not blown,...

Wobbling fan

Hi there, thanks for writing in. I'd be happy to help. I suggest, with the engine off, to try and move the fan up and down to see if there is any looseness in the water pump or in the...

Car starts after a few tries, but then dies as soon as I take my foot off gas pedal.

Clean any debris on the battery posts using a mixture of baking soda and water. Under your battery is a pedal that connects to the PCM. Make sure that it is pushed down hard so that your battery does not...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com