Buick LeSabre Car Thermostat Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Car Thermostat Replacement Service

How much does a Car Thermostat Replacement cost?

On average, the cost for a Buick LeSabre Car Thermostat Replacement is $205 with $65 for parts and $140 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1998 Buick LeSabreV6-3.8L	Service typeCar Thermostat Replacement	Estimate$323.72	Shop/Dealer Price$369.50 - $498.74
2004 Buick LeSabreV6-3.8L	Service typeCar Thermostat Replacement	Estimate$332.91	Shop/Dealer Price$378.01 - $508.76
1996 Buick LeSabreV6-3.8L	Service typeCar Thermostat Replacement	Estimate$308.31	Shop/Dealer Price$350.75 - $473.88
2002 Buick LeSabreV6-3.8L	Service typeCar Thermostat Replacement	Estimate$318.31	Shop/Dealer Price$363.25 - $493.88
1999 Buick LeSabreV6-3.8L	Service typeCar Thermostat Replacement	Estimate$318.31	Shop/Dealer Price$364.72 - $496.46
2003 Buick LeSabreV6-3.8L	Service typeCar Thermostat Replacement	Estimate$318.31	Shop/Dealer Price$363.39 - $494.13
1991 Buick LeSabreV6-3.8L	Service typeCar Thermostat Replacement	Estimate$309.21	Shop/Dealer Price$351.89 - $475.71
1994 Buick LeSabreV6-3.8L	Service typeCar Thermostat Replacement	Estimate$309.25	Shop/Dealer Price$351.92 - $475.76

Show example Buick LeSabre Car Thermostat Replacement prices

What is an engine cooling system thermostat and how does it work?

The car's engine cooling system thermostat is a small valve within a cooling system passageway that opens and closes in response to the temperature of the circulating engine coolant. When your car is first started and the coolant is cold, the valve in the thermostat will be in the closed position, circulating the coolant flow only within the engine instead of flowing to the radiator, which allows the engine to warm up fast, promoting fuel efficiency, low emissions, and reduced engine deposits. Once the engine coolant reaches the design temperature, usually around 195 degrees, the valve will open and close as you drive in order to maintain a coolant temperature typically between 195 to 225 degrees Fahrenheit.

Thermostat

When to consider replacing the engine cooling system thermostat:

Engine overheats. A thermostat with the valve stuck closed is a common cause of engine overheating. However, since there are other causes of overheating, a mechanic will thoroughly inspect the cooling system prior to condemning the thermostat. Since it is usually not known how badly the engine overheated, the mechanic will also try to determine if there is evidence that the cylinder head gasket was blown. If so, it would be repaired prior to replacing the thermostat.
Temperature gauge reads too low or too high. Thermostats can get sticky, causing the engine temperature to stray from the optimal range. Your dash-mounted temperature gauge will notify you of this malfunction.
Cooling system repairs. All thermostats eventually fail. Therefore, if the cooling system is already open for major repairs, such as water pump or radiator replacement, it is recommended to install a new thermostat simply as insurance against future breakdown.

How do mechanics replace the engine cooling system thermostat?

Once the engine is completely cold, the radiator cap is loosened and enough coolant is drained from the radiator so the coolant level is below the thermostat housing.
The thermostat housing is removed and the thermostat and gasket are extracted. Note that some cars have more than one cooling system thermostat and both might need replacement.
All mounting surfaces on the thermostat housing are cleaned of old gasket material. A new gasket is applied and the thermostat is re-installed in the correct orientation and with the temperature sensing cylinder facing downward towards the engine.
The thermostat housing bolts are tightened to original equipment manufacturer (OEM) specifications using a calibrated inch-pound torque wrench.
The cooling system is refilled with the appropriate coolant type and the system is fully bled of all air.
The car engine is run until the normal operating temperature is reached, and while taking precautions with the hot coolant, the coolant level is rechecked while confirming there is flow through the radiator — either visually or with an infrared temperature gun. This will confirm the thermostat is open. Finally, the engine is checked for leaks.

Is it safe to drive with an engine cooling system thermostat problem?

No. If it has been determined that there is a thermostat problem, it should be repaired right away. Failure to do so can cause substantial and costly damage to the engine.

When replacing the engine cooling system thermostat keep in mind:

Engine overheating due to causes other than a faulty thermostat, will themselves damage a thermostat. Therefore, always replace the thermostat if the engine overheats, even if the thermostat was not the initial cause of the overheating.
The thermostat should be replaced anytime you have major work done on the coolant system. It is convenient and costs little during such repairs and insurance against future breakdown.
OEM thermostats are the best ones to use and you can request your mechanic to install only the OEM thermostat. Dealer supplied, OEM thermostats are sometimes more costly but are generally higher quality and specifically engineered for your car.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Buick mechanics

Real customer reviews from Buick owners like you.

Excellent Rating

(3)

Rating Summary

3

0

0

0

0

3

0

0

0

0

SEE REVIEWS NEAR ME

Excellent Rating

(3)

Rating Summary

3

0

0

0

0

3

0

0

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

P3483 OBD-II Trouble Code: Cylinder 11 Deactivation/Intake Valve Control Circuit Low

P3483 code means that the intake control solenoid for the #11 cylinder is open, shorted or pushing back with a lot of resistance due to a short.

A Buyer’s Guide to the 2012 Acura TSX

The The 2012 Acura TSX is a luxury midsize sedan that comes with superior comfort and convenience. This vehicle offers excellent fuel economy, reliability, and a simple pricing structure for a variety of different budgets. It drives easily down the...

The Best Used Cars to Buy If You Have Limited Mobility

When When you have limited mobility there are a number of challenges you face, one of these can be with your vehicle. Finding a car that meets your specific needs, and addressing your challenges can mean the difference between being...

How does the front passenger power window switch work?

Your car is equipped with power windows in the front and rear (unless you drive a coupe, in which case you only have front windows anyway). The passenger side power window switch offers the ability to do three things: Roll...

2007 Chrysler Sebring loses power at right turns, rare occasions

If all future instances of stalling are on right turns, and none are on left turns, a possibility is a chafing wire harness that only comes into play on right turns. Does the car stall at ANY stops (traffic lights,...

I have a 95 Jeep Wrangler 4 cylinder. It has been running awesome until the other day when I put it in reverse. Backed up and depresses the clutch and brake to stop to shift into first and park it. When I hit the brake the engine was definitely under a little load. You could feel it still trying to pull. I could not get it out of reverse. I shut it off and wiggled it for a little and it came right out and ran fine the rest of the night. Now it is happening more often. I’ll start it in first with clutch depressed and it pulls a little. Early tonight I checked the fluid in the transmission and it was full. I started in neutral and I could not get it to go into a gear at all! Shut it off and it would not go into a gear. Let it sit about 5 minutes and it went into a gear and ran fine.

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com