BMW M550i xDrive Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(6,667)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(6,667)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a BMW M550i xDrive Brake Drum Replacement is $862 with $700 for parts and $161 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2019 BMW M550i xDriveV8-4.4L TurboService typeBrake Drum ReplacementEstimate$1595.96Shop/Dealer Price$1963.09 - $3026.20
2018 BMW M550i xDriveV8-4.4L TurboService typeBrake Drum ReplacementEstimate$1561.96Shop/Dealer Price$1929.12 - $2992.25
Show example BMW M550i xDrive Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(6,667)

Rating Summary
6,214
206
60
44
143
6,214
206
60
44
143

Charles

34 years of experience
342 reviews
Charles
34 years of experience
BMW 525i L6-3.0L - Drive Belt Tensioner Replacement - Manor, Texas
Charles is awesome will always request him & will tell friends and family

Gustavo

15 years of experience
60 reviews
Gustavo
15 years of experience
BMW 328i xDrive L4-2.0L Turbo - Spark Plugs - Fair Lawn, New Jersey
Timely, very helpful and knowledgeable. Would definitely recommend.

Amor

43 years of experience
181 reviews
Amor
43 years of experience
BMW 750iL V12-5.4L - Oil Change - San Jose, California
excellent work and knowledge of issues and friendliness .

Robert

31 years of experience
641 reviews
Robert
31 years of experience
BMW 325i L6-3.0L - Oil Change - San Jose, California
Robert was punctual and professional as always.

Excellent Rating

(6,667)

Rating Summary
6,214
206
60
44
143
6,214
206
60
44
143
Number of BMW services completed
73337+
services done by our mechanics
TOTAL NUMBER OF EXPERT BMW MECHANICS
1100+
experts on our platform

Recent articles & questions

How Long Does an Exhaust Gas Recirculation (EGR) Tube Last?
The The exhaust gas recirculation (EGR) tube is part of your vehicle's EGR (exhaust gas recirculation) system and is part of the EGR valve. The EGR valve works to recirculate the exhaust gas your car produces so that you aren't...
P2110 OBD-II Trouble Code: Throttle Actuator Control System Forced Limited RPM
P2110 P2110 trouble code definition Throttle Actuator Control System Forced Limited RPM What the P2110 code means P2110 is an OBD-II generic code for the engine control module (ECM) detecting a major failure in the throttle actuator control (TAC) system...
The Traveler’s Guide to Driving in Switzerland
Switzerland Switzerland is a gorgeous country, and there are many different places to visit and things to do when you use this area. The landscapes are stunning, and you may want to visit places such as Lake Luzern, Lake Geneva,...

Codes P0121, P0221, P2101, P2104, P2110, P2111

Here are the codes, what they mean and the potential causes below each of them. Note that some of them may be related and can cause additional codes to be triggered that may be fixed when one of it's related...

Only when it's really hot outside the temperature gauge reaches almost about less then half way. Car won't start up again till coo

There may be 2 issues to deal with here. The inability of the engine to reach "normal operating temperature" (always the center of the gauge), indicates either a weak or failed thermostat, or a failed coolant temperature sending unit/coolant temp...

Well my pick up 2017 Nissan [Frontier](/topics-frontier/) Np300 the clucth will not engage

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com