BMW M240i Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(12)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(12)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a BMW M240i Tie Rod End Replacement is $186 with $91 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2017 BMW M240iL6-3.0L TurboService typeTie Rod End - Rear Left Outer ReplacementEstimate$436.43Shop/Dealer Price$519.29 - $736.37
2017 BMW M240iL6-3.0L TurboService typeTie Rod End - Rear Right Inner ReplacementEstimate$427.42Shop/Dealer Price$512.31 - $730.92
2017 BMW M240iL6-3.0L TurboService typeTie Rod End - Rear Left Inner ReplacementEstimate$427.42Shop/Dealer Price$512.31 - $730.91
2017 BMW M240iL6-3.0L TurboService typeTie Rod End - Rear Right Outer ReplacementEstimate$408.43Shop/Dealer Price$491.28 - $708.35
2018 BMW M240iL6-3.0L TurboService typeTie Rod End - Rear Left Outer ReplacementEstimate$370.43Shop/Dealer Price$449.32 - $663.43
2017 BMW M240iL6-3.0L TurboService typeTie Rod End - Front Left Outer ReplacementEstimate$282.37Shop/Dealer Price$339.23 - $487.28
2018 BMW M240iL6-3.0L TurboService typeTie Rod End - Front Left Outer ReplacementEstimate$287.37Shop/Dealer Price$344.10 - $492.04
2018 BMW M240iL6-3.0L TurboService typeTie Rod End - Front Right Inner ReplacementEstimate$375.43Shop/Dealer Price$454.54 - $668.82
Show example BMW M240i Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(12)

Rating Summary
11
0
0
0
1
11
0
0
0
1

Albin

6 years of experience
17 reviews
Albin
6 years of experience
BMW 328i xDrive L6-3.0L - Tie Rod End Replacement (Front Left Inner, Front Left Outer) - Brooklyn, New York
He’s a cool dude no dull moments talked to me while fixing the whole thing excellent job

Chuck

10 years of experience
351 reviews
Chuck
10 years of experience
BMW 328i xDrive L6-3.0L - Tie Rod End Replacement (Front Left Inner, Front Right Inner, Front Left Outer, Front Right Outer) - Allen, Texas
I was glad i had Chuck come over to work on my car. He was very professional. He encountered several unexpected issues while performing the job due to frozen parts but he knows exactly what to do and how to do it. He suggested me additional details and information regarding some other issues to be taken care of as well. It’s definitely worth every penny we spent on this job. Thanks chuck.

Chuck

10 years of experience
351 reviews
Chuck
10 years of experience
BMW 328i L6-3.0L - Tie Rod End Replacement (Front Right Inner) - Richardson, Texas
Great job

Jamie

22 years of experience
94 reviews
Jamie
22 years of experience
BMW 328i L6-3.0L - Tie Rod End Replacement (Front Right Inner, Front Right Outer) - Hemet, California
It was really straightforward Jamie explained how long it would take and we ended up having a great in-depth conversation.

Excellent Rating

(12)

Rating Summary
11
0
0
0
1
11
0
0
0
1
Number of BMW Tie Rod End Replacement services completed
132+
services done by our mechanics
TOTAL NUMBER OF EXPERT BMW MECHANICS
1100+
experts on our platform

Recent articles & questions

The Best Used Cars to Buy For Fuel Economy
Saving money on gas is an important factor to consider when buying a car. The Honda Civic, Toyota Prius, and Ford Fusion all have great fuel economy.
Symptoms of a Bad or Failing Power Steering Pressure Switch
If you notice your engine slows down, stalls, or speeds up then slows down, have your power steering pressure switch inspected and replaced.
P0881 OBD-II Trouble Code: Traction Control Module (TCM) Power Input Signal Range/Performance
P0881 means the traction control module is not working properly, possibly due to a faulty ON/OFF switch or damaged electrical components.

ABS runs key out

The ABS pump is fed power directly from a fusible link and not the 10A brake fuse. If the pump is running non-stop, this is an indication of a faulty brake pressure modulator valve unit that will need to be...

Engine malfunction light, reduced engine power, engine powered down

Hi there. There are a lot of things that can cause this on your 2012 BMW M5. I usually start by scanning the computer for codes to see what comes up. If there are not codes then I load test...

my coil spring is corroded and i want to buy the part but I can't identify the exact name of the part i know its a coil spring

You should get the new coil spring with the coil spring insulators. I would recommend replacing the front shocks and sway bar links with bushings at the same time.

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com