BMW 740i Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a BMW 740i Brake Drum Replacement is $362 with $219 for parts and $142 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2013 BMW 740iL6-3.0L Turbo	Service typeBrake Drum Replacement	Estimate$693.58	Shop/Dealer Price$847.86 - $1243.75
1993 BMW 740iV8-4.0L	Service typeBrake Drum Replacement	Estimate$590.80	Shop/Dealer Price$728.56 - $1078.72
2017 BMW 740iL6-3.0L Turbo	Service typeBrake Drum Replacement	Estimate$1561.96	Shop/Dealer Price$1929.11 - $2992.25
2018 BMW 740iL6-3.0L Turbo	Service typeBrake Drum Replacement	Estimate$1561.96	Shop/Dealer Price$1929.07 - $2992.18
2016 BMW 740iL6-3.0L Turbo	Service typeBrake Drum Replacement	Estimate$922.62	Shop/Dealer Price$1142.76 - $1736.00
2019 BMW 740iL6-3.0L Turbo	Service typeBrake Drum Replacement	Estimate$1561.96	Shop/Dealer Price$1929.11 - $2992.25
2011 BMW 740iL6-3.0L Turbo	Service typeBrake Drum Replacement	Estimate$668.08	Shop/Dealer Price$822.01 - $1217.63
1994 BMW 740iV8-4.0L	Service typeBrake Drum Replacement	Estimate$598.80	Shop/Dealer Price$737.22 - $1087.87

Show example BMW 740i Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(46)

Rating Summary

44

0

1

1

0

44

0

1

1

0

SEE REVIEWS NEAR ME

Matthew

33 years of experience

1229 reviews

Request Matthew

Matthew

33 years of experience

Request Matthew

by Irvin

BMW 740i V8-4.4L - Car is not starting - Newport News, Virginia

Great guy

Robert

20 years of experience

1098 reviews

Robert

20 years of experience

by Jerry

BMW 740i V8-4.0L - Car is not starting - Denver, Colorado

Robert was very knowledgeable about BMW’s he knew exactly what to look for and I would recommend him to any BMW owners that need a Mechnaic.

Chet

41 years of experience

493 reviews

Chet

41 years of experience

by Darryl

BMW 740i V8-4.4L - Car shuts off when stepping on gas pedal Inspection - San Diego, California

Understood the vehicle and was professional the entire time he worked on it. He diagnosed the problem and helped identify other problem areas that were hurting the cars performance. My car runs exceptionally well now. Next time I'm stuck with a problem and need a mechanic who understands German cars I will call Chet. My car: 1998 BMW 740i 120,000 miles on it. The work done by Chet: chased and diagnosed an electrical problem that was messing up the air fuel ratio causing the car to not operate.

Noe

36 years of experience

604 reviews

Noe

36 years of experience

by DA

BMW 740i L6-3.0L Turbo - Oil Change - Woodinville, Washington

very good

Excellent Rating

(46)

Rating Summary

44

0

1

1

0

44

0

1

1

0

SEE REVIEWS NEAR ME

Recent articles & questions

5 Essential Things to Know About Baby Car Seats

Parents Parents always want to do their best to keep their children safe no matter where they are. When the kids are in the vehicle, this means that they need to buckle up, and if they are very young, they...

Symptoms of a Bad or Failing Brake Booster Vacuum Pump

Diesel vehicles that have a stiff brake pedal with power brakes working intermittently may need to have the brake booster vacuum pump replaced.

How to Drive Your Manual Transmission Car With a Broken Clutch

If you drive a car with a manual transmission, there will likely come a point in time when the clutch wears out (https://www.yourmechanic.com/article/how-long-does-a-clutch-last)...

what are the signs that i an engine mount is breaking?

The most noticeable sign of a failing motor mount is a very strong vibration that may increase a bit as the engine speed increases. As you may know, the motor mounts (https://www.yourmechanic.com/services/engine-mount-replacement) support the motor inside the car's chassis and...

The car turns over but doesn't actually starts

An engine is stalling inspection (https://www.yourmechanic.com/services/car-is-stalling-inspection) will reveal the cause. When the vehicle is cold, the mixture has to be enriched in order for the engine to run initially. That enrichment signal is sent (to the fuel injectors) if the...

Intake air flow leaking. What makes this happen?

Hi there. When having the code P0171 (https://www.yourmechanic.com/article/p0171-obd-ii-trouble-code-system-too-lean-bank-1-by-andrew-quinn), the fuel system is too lean. This could be the fuel pump is not working, the fuel filter is dirty or plugged, or the injectors are plugged or not working properly. Check...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com