BMW 430i xDrive Gran Coupe Water Pump Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(4)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(4)

Water Pump Replacement Service

How much does a Water Pump Replacement cost?

On average, the cost for a BMW 430i xDrive Gran Coupe Water Pump Replacement is $575 with $337 for parts and $238 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2017 BMW 430i xDrive Gran CoupeL4-2.0L TurboService typeWater Pump ReplacementEstimate$938.32Shop/Dealer Price$1113.15 - $1623.85
2018 BMW 430i xDrive Gran CoupeL4-2.0L TurboService typeWater Pump ReplacementEstimate$1112.79Shop/Dealer Price$1287.00 - $1797.24
Show example BMW 430i xDrive Gran Coupe Water Pump Replacement prices

What is a water pump and how does it work?

The water pump is a belt or chain-driven engine accessory bolted to the engine above the crankshaft pulley. The pump housing has an impeller that circulates engine coolant through the cooling system passageways in the engine block and cylinder head, on to the radiator, where the coolant temperature is reduced. . The lower temperature coolant then flows back to the water inlet on the engine and the water pump continues the cycle.

When to consider replacing the water pump:

  • Coolant leaks or overheating. The water pump impeller shaft is supported by a bearing. Eventually, the bearing or seal can wear and leak or damage the impeller. Many water pumps have weep holes near the pump bearing. If you see significant leakage from that weep hole, it is time to replace the pump.
  • Bearing roughness or noise. If the water pump shaft does not turn smoothly or the pump is noisy, the bearing is excessively worn. Pump replacement will be necessary.
  • Timing belt replacement. In engines where the water pump is driven by the timing belt, it is a good idea to replace the water pump at the same time the timing belt is replaced. The extensive work explains why it is always recommended to replace the water pump whenever the mechanic already has these components removed for regularly scheduled timing belt replacement.

How do mechanics replace the water pump?

  • The water pump is usually bolted to the front of the engine. The replacement procedure will vary depending on whether the pump is driven by the timing belt, the serpentine belt, or chain.
  • On a cold engine, the engine coolant is drained to a level below the water pump.
  • Components that require removing to access the water pump are removed, including the belt or chain that directly drive the pump.
  • The bolts holding the pump to the engine are removed and the pump is pulled out.
  • The gasket surface must be cleaned and the pump mounting surface inspected. A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench.
  • For applications where the water pump is driven by the timing belt, the timing belt must be removed. Typically, this requires removal of the crankshaft pulley, timing belt covers, and timing belt tensioner. Once the new pump is installed, new coolant is added back while bleeding the cooling system of any air. The engine is then run and brought to normal operating temperature to check for leaks and ensure normal operating temperature.

Is it safe to drive with a water pump problem?

No. Should the water pump only leak a little bit, you can drive the car. However, a small leak could suddenly enlarge or the pump bearing might unexpectedly seize. Either circumstance would likely cause engine overheating. If a defective water pump causes the overheating, it is not safe to drive because of the damage to the engine.

When replacing the water pump keep in mind:

  • It is best to install a new cooling system thermostat when you install a new water pump, especially if the thermostat is old or original.
  • Completely flushing the cooling system is a good idea when you replace the water pump. Flushing can be done before or after pump replacement.
  • The rest of the cooling system should be inspected too — particularly rubber hoses, which have a limited lifetime.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(4)

Rating Summary
4
0
0
0
0
4
0
0
0
0

Mike

27 years of experience
265 reviews
Mike
27 years of experience
BMW 430i xDrive Gran Coupe L4-2.0L Turbo - Oil Change - Farmington, Michigan
Mike was very knowledgeable and honest. Definitely couldn't of found a better mechanic. Thanks Mike!

Chuck

18 years of experience
464 reviews
Chuck
18 years of experience
BMW 430i xDrive Gran Coupe L4-2.0L Turbo - Brake Pads Replacement (Front) - Dallas, Texas
Excellent

Tinashe

14 years of experience
781 reviews
Tinashe
14 years of experience
BMW 430i xDrive Gran Coupe L4-2.0L Turbo - Brake Pads Replacement (Rear) - Norcross, Georgia
An absolute delight. Super knowledgeable and nice as can be. Would highly recommend.

Chuck

18 years of experience
464 reviews
Chuck
18 years of experience
BMW 430i xDrive Gran Coupe L4-2.0L Turbo - Oil Change - Dallas, Texas
Chuck is an excellent technician. On-time, friendly, and extremely knowledgeable.

Excellent Rating

(4)

Rating Summary
4
0
0
0
0
4
0
0
0
0
Number of BMW 430i xDrive Gran Coupe services completed
44+
services done by our mechanics
TOTAL NUMBER OF EXPERT BMW MECHANICS
1200+
experts on our platform

Recent articles & questions

P001A OBD-II Trouble Code: "A" Camshaft Profile Control Circuit/Open
P001A means the camshaft and crankshaft signals have malfunctioned which may cause a poorly running engine, reduced power or a no-start condition.
P2006 OBD-II Trouble Code: Intake Manifold Runner Control Stuck Closed Bank 1
P2006 trouble code definition The P2006 code is a generic OBD2 diagnostic trouble code relating to the intake manifold runner control circuit....
Symptoms of Bad or Failing Suspension Springs
Common signs include the vehicle tilting to one side, uneven tire wear, bouncing while driving, and bottoming out.

Windshield wiper fluid won't spray

The symptoms you describe lead me to believe you have either a washer pump motor that has failed or the connection to the washer pump motor has a break in it. To be 100% certain it may be time to...

Crankshaft position sensor bolt broke off

You may need to remove the throttle body to gain access to remove the broke off screw. This would be the best way to get access to remove the broken bolt.

Switched to 4WD - did fine for a little then started making grinding noise. Now car won't move and the 4WD light is blinking.

Hi there. If the 4WD light is blinking and you hear a grinding noise when the transmission is in drive or reverse only, then the transfer case has either broken the fork inside the case or the syncronizer jammed up...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com