Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM.
How A Diagnostic Works
Instantly book a certified mobile mechanic to come to you
Mechanic diagnoses the problem and quotes necessary repairs
Your vehicle is ready to go
Fair, upfront & transparent pricing for all services
Our certified mobile mechanics can come to you now.
On average, the cost for a BMW 330e Brakes must be pumped to work Inspection is $95 with $0 for parts and $95 for labor. Prices may vary depending on your location.
| Car | Service | Estimate | Shop/Dealer Price |
|---|---|---|---|
| 2016 BMW 330eL4-2.0L Turbo Hybrid | Service typeBrakes must be pumped to work Inspection | Estimate$114.99 | Shop/Dealer Price$124.99 - $132.49 |
| 2018 BMW 330eL4-2.0L Turbo Hybrid | Service typeBrakes must be pumped to work Inspection | Estimate$94.99 | Shop/Dealer Price$105.01 - $112.52 |
| 2021 BMW 330eL4-2.0L Turbo Hybrid | Service typeBrakes must be pumped to work Inspection | Estimate$94.99 | Shop/Dealer Price$105.01 - $112.52 |
| 2022 BMW 330eL4-2.0L Turbo Hybrid | Service typeBrakes must be pumped to work Inspection | Estimate$94.99 | Shop/Dealer Price$104.99 - $112.48 |
| 2017 BMW 330eL4-2.0L Turbo Hybrid | Service typeBrakes must be pumped to work Inspection | Estimate$94.99 | Shop/Dealer Price$105.02 - $112.55 |
When you slow your car or decide to stop, you press the brake pedal. Most of the time, the pedal will be firm and you’ll be able to apply steady pressure until you reach the desired slower speed, or come to a complete stop. However, sometimes the pedal may “go to the floor” and you’ll have to pump it a couple of times to get the firm feel that you’re used to. If your brakes must be pumped to work, there’s a serious issue that needs to be addressed.
Your brakes work on fluid pressure. If the braking system isn’t able to build up the pressure necessary to operate the system, your pedal will feel strange. In some cases, it will be spongy and soft. In others, you’ll have to pump the brakes.
When you press the brake pedal, the master cylinder sends fluid into the lines, creating pressure. This activates the calipers, which squeeze the rotor on each wheel between the brake pads. Drum brakes work on a similar basis, but fluid pressure causes the actuator to press the shoes out against the sides of the drum to slow down the wheels.
Obviously, if there isn’t enough pressure in the lines, this doesn’t happen. However, if moisture has gotten into the system, the result can be similar. Water has a lower boiling point than brake fluid. When it’s heated at the brakes, it vaporizes, creating air in the lines (and allowing compression – brake fluid cannot be compressed).
Air in the Lines: The number one most common cause for having to pump your brakes to get them to work is air in the lines. This may be because your brakes were recently serviced but not bled correctly. It requires bleeding each wheel several times, starting with the wheels farthest from the master cylinder (passenger rear, driver rear, then passenger front and driver front). It can take multiple bleeds to remove all the air from the lines, even after a basic service. The fluid will then need to be topped off.
Low Brake Fluid: If your brake fluid is low (and it’s not due to brake pad wear), then the system will be unable to create enough pressure for normal operation and you may have to pump the pedal. Generally, low fluid is caused by a leak somewhere in the system, including at the caliper, the brake lines, or even the master cylinder.
Failing Master Cylinder: While rare, master cylinder failure does occur. If the master cylinder has begun leaking fluid down the back of the engine, you can expect to experience poor brake operation and reduced safety on the road.
Moisture in the Fluid: If your brake fluid has absorbed moisture (which is normal over time and through regularly wear and tear), you’ll notice reduced braking performance, including the possibility that you’ll have to pump the brake pedal in some situations.
Damaged or Missing Bleeder Valve: Each wheel should have a brake fluid bleeder valve on the line near the wheel hub. If one of yours has been damaged, it’s possible that you’re leaking fluid and allowing air into the line at the same time.
A top-rated mobile mechanic will come to your home or office to inspect your car’s brake system. The mechanic will visually inspect the master cylinder, the brake lines, calipers, and the rest of the system in order to determine the underlying cause of the problem. The mechanic will then provide a detailed inspection report that includes the scope and cost of the necessary repairs.
The mechanic will need to inspect the entire brake system, which may require the removal of one or more wheels. The mechanic will also need to check for air in the lines, as well as leaks in the lines and at the master cylinder.
If your brakes have to be pumped to work, your system needs immediate service. This indicates a significant problem, including air in the lines. It reduces your stopping capability on the road, which endangers you, your passengers, as well as others on the road. One of our mechanics can diagnose and repair the problem, ensuring that you’re safe while driving.
Fast and easy service at your home or office
Backed by 12-month, 12.000-mile guarantee
Real customer reviews from BMW owners like you.
Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.
