BMW 1 Series M Intake Manifold Gaskets Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(21)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(21)

Intake Manifold Gaskets Replacement Service

How much does a Intake Manifold Gaskets Replacement cost?

On average, the cost for a BMW 1 Series M Intake Manifold Gaskets Replacement is $664 with $174 for parts and $490 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2011 BMW 1 Series ML6-3.0L TurboService typeIntake Manifold Gaskets ReplacementEstimate$891.48Shop/Dealer Price$1010.23 - $1295.59
Show example BMW 1 Series M Intake Manifold Gaskets Replacement prices

What is an intake manifold gasket and how does it work?

The intake on an engine may be made up of a lower intake manifold and an upper intake manifold or plenum. The lower intake manifold is a cast aluminum or molded plastic chamber bolted to the cylinder head of the engine. The intake manifold must be tightly sealed to the cylinder head(s) using a gasket in order to prevent air, oil, or engine coolant leaks.

When to consider replacing the intake manifold gasket:

Internal or external leaks. Due to constant temperature expansion and contraction of engine parts or overheating, the gasket’s ability to seal properly can be ruined, resulting in problems such as:

  • Internal or external engine coolant leaks. In some applications, the manifold has cooling passages within. If the manifold seal to the engine fails, coolant can leak externally or even into the engine oil crankcase, where coolant can be noticed in the engine oil.
  • Engine overheating. If the leak at the manifold is a leak of engine coolant, it can lead to engine overheating. However, there are other causes of engine overheating, so a mechanic would have to determine the actual cause.
  • External oil leaks. On some 6 and 8 cylinder engines, the intake manifold sits atop an oil-lubricated area of the engine block. If the manifold gasket has failed, oil can leak from the block to the exterior of the engine.
  • Poor engine operation, lean operation, rough idle. Vacuum air leaks into the manifold due to a defective gasket that will upset the air-fuel ratio. The engine may run poorly.
  • Check engine light. Minor leaks at the intake manifold gasket will not usually cause the check engine light to illuminate. However, as a leak persists, it may grow larger and it possible for the leak to degrade engine performance enough that it will cause a trouble code to set, which will cause the check engine light to illuminate.

How do mechanics replace the intake manifold gasket?

  • Working on a cold engine, the engine cover is removed. If the intake manifold has internal cooling system passageways, the engine coolant is drained below the level of those passageways.
  • The accelerator cable assembly and cruise control cable are removed and set aside. All electrical connections and emission and vacuum lines in the way of the intake are removed. Ignition components, such as the coil, are removed as needed. If the car has an upper plenum, that is removed and set aside.
  • If the fuel rail is bolted to the intake manifold, the supply and return connections to the fuel rail are disconnected.
  • Once all connections to the manifold are clear, the manifold is unbolted and removed from the engine.
  • Aluminum and plastic manifolds are checked with a machinist’s straightedge to ensure the surface flatness does not exceed the original equipment manufacturer’s specification. If the surface of a manifold is not flat, the new gasket will not seal properly. Plastic manifolds are checked for cracks, heat damage, and warpage.
  • Once the manifold is deemed re-usable or replaced as needed, the new gasket is applied, the manifold is put in position and the mounting bolts are torqued with a calibrated torque wrench in the OEM specified sequence. In some applications, RTV sealant must be applied in corners of the mounting surface or specified hard-to-seal spots, per the service manual.
  • All removed components are then re-installed in the reverse of the above steps.
  • Finally, the vehicle is run and checked for leaks, and test driven.

Is it safe to drive with an intake manifold gasket problem?

Yes. The principal concern with a leaking intake manifold gasket is potential damage to the engine, depending on where the leak is. Although the vehicle will generally be safe to drive, you should schedule service as soon as possible to minimize the chances of additional costly damage. If the leak involves coolant, it could lead to engine overheating damage or the coolant could contaminate the engine oil, which can damage the engine bearings. If there is an air leak to the cylinders, it can cause lean operation which could overheat the catalytic converter.

When replacing the intake manifold gasket keep in mind:

  • In engines where coolant flows through the intake manifold, a leaking intake manifold gasket can be either the cause of or result of engine overheating. If you have a leaking intake manifold gasket, and the engine has overheated, the entire engine should be inspected for damage, such as a blown head gasket. The engine cooling system thermostat should be replaced because engine overheating can damage the cooling system thermostat.
  • Some car engine designs are more likely than others to experience leaking intake manifold gaskets due to material and design issues. Your mechanic can inform you if your car represents one of these cases. Many times a re-designed gasket, or altered installation technique and torque values, will be relevant to avoid a recurrence of any leaks. Mechanics will consult Technical Service Bulletins to determine if any unique circumstance exists for your car.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(21)

Rating Summary
20
0
0
0
1
20
0
0
0
1

Emmette

37 years of experience
282 reviews
Emmette
37 years of experience
BMW 328i L6-3.0L - Intake Manifold Gaskets - Fairfax, Virginia
He is very professional

Amor

44 years of experience
181 reviews
Amor
44 years of experience
BMW 525i L6-2.5L - Intake Manifold Gaskets - Sunnyvale, California
He is very good and knows his way around the car

John

37 years of experience
565 reviews
John
37 years of experience
BMW X1 L4-2.0L Turbo - Intake Manifold Gaskets - Folsom, California
John was very knowledgeable about his work. He was on time and completed the repair quickly and diligently. I appreciate his work and highly recommend him.

Aaron

30 years of experience
132 reviews
Aaron
30 years of experience
BMW X5 L6-3.0L - Intake Manifold Gaskets - Tallahassee, Florida
Aaron is very good guy that knows his job well and very understandable when asking questions that I didn't know about on this vehicle he broke it down to where things were happening to this vehicle that I wasn't sure. I would definitely recommend his service on my mechanic web site

Excellent Rating

(21)

Rating Summary
20
0
0
0
1
20
0
0
0
1
Number of BMW Intake Manifold Gaskets Replacement services completed
231+
services done by our mechanics
TOTAL NUMBER OF EXPERT BMW MECHANICS
1200+
experts on our platform

Recent articles & questions

How Long Does an Idle Control Valve Last?
Among Among the most important factors in having a smooth running car is a consistent idle speed. Having the incorrect idle speed can lead to a variety of different issues. There are a number of different components that have to...
Understanding Toyota Maintenance Required Lights
Car symbols, or dashboard lights, are a car service reminder. The Toyota Maintenance Required lights indicate when and what service your car needs.
How Long Does an Exhaust System Hanger Last?
Your Your exhaust system takes quite a beating while it is suspended under your car. Think about it - you're traveling at high speeds, over bumps, through unfavorable road conditions, and much more. If it wasn't properly affixed to the...

Belt or bearing going bad.

The noise you are hearing is coming from one of the bearings of the tensioner pulley, water pump, alternator, A/C pulley and possibly even the power steering pump if the noise is a bearing noise. Sometimes just a belt noise...

What else can cause an over heating engine. .

Overheating in stop and go traffic can be due to non functioning electric radiator cooling fans. A poorly functioning water pump can be a cause, too, for example if the drive belt is not tight enough. If the car is...

2013 nissan altima blowing hot air

Hi There, It sounds like you may have a bad AC condenser (https://www.yourmechanic.com/services/ac-condenser-replacement) that may have been damaged in the accident. The A/C uses a compressor to turn a refrigerant gas, usually Freon, into a liquid concentrating its heat. In...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com