Acura Legend Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Acura Legend Brake Drum Replacement is $306 with $144 for parts and $161 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1987 Acura LegendV6-2.7L	Service typeBrake Drum Replacement	Estimate$484.04	Shop/Dealer Price$585.94 - $824.67
1989 Acura LegendV6-2.7L	Service typeBrake Drum Replacement	Estimate$450.04	Shop/Dealer Price$551.99 - $790.77
1991 Acura LegendV6-3.2L	Service typeBrake Drum Replacement	Estimate$585.72	Shop/Dealer Price$721.59 - $1062.12
1988 Acura LegendV6-2.7L	Service typeBrake Drum Replacement	Estimate$450.04	Shop/Dealer Price$551.92 - $790.64
1994 Acura LegendV6-3.2L	Service typeBrake Drum Replacement	Estimate$585.72	Shop/Dealer Price$721.63 - $1062.20
1995 Acura LegendV6-3.2L	Service typeBrake Drum Replacement	Estimate$585.72	Shop/Dealer Price$721.59 - $1062.12
1986 Acura LegendV6-2.5L	Service typeBrake Drum Replacement	Estimate$600.38	Shop/Dealer Price$737.38 - $1082.23
1990 Acura LegendV6-2.7L	Service typeBrake Drum Replacement	Estimate$458.54	Shop/Dealer Price$561.19 - $800.49

Show example Acura Legend Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Acura mechanics

Real customer reviews from Acura owners like you.

Excellent Rating

(43)

Rating Summary

39

2

1

0

1

39

2

1

0

1

SEE REVIEWS NEAR ME

Manuel

32 years of experience

579 reviews

Manuel

32 years of experience

by Tina

Acura Legend V6-3.2L - Inspection / Diagnostics - Rancho Santa Margarita, California

Manuel was great and on time!

Carlos

25 years of experience

122 reviews

Carlos

25 years of experience

by Keven

Acura Legend V6-3.2L - Clunking noise when I drive over bumps - San Pablo, California

Good mechanic.

Joshua

27 years of experience

709 reviews

Joshua

27 years of experience

by Gwen

Acura Legend V6-3.2L - Timing Belt - Richmond, California

Great service.

Richard

21 years of experience

461 reviews

Request Richard

Richard

21 years of experience

Request Richard

by Loddie

Acura Legend V6-3.2L - radiator cap - Douglasville, Georgia

YourMechanic sent the wrong radiator cap twice. Richard went above and beyond his call of duty and searched and located a radiator cap that fit my vehicle. I was ready to call YourMechanic and tell them to come and take the radiator out and refund my money. Richard saved the day and the company. Thanks Richard!!

Excellent Rating

(43)

Rating Summary

39

2

1

0

1

39

2

1

0

1

SEE REVIEWS NEAR ME

Recent articles & questions

How to Buy a Good Quality Throttle Body

Just Just like the throttle, the throttle body plays a very important part in how your fuel-injected engine runs, and makes the car move. The air intake system relies on the throttle body as a pivotal component. The air intake...

How to Drop a Gas Tank

The The fuel tank on your car is typically located under the rear or middle of the vehicle. There can be a number of reasons why you would need to remove it; the most common reason is needing to replace...

How to Remove Cylinder Head Bolts

Removing Removing the head is a major step in removing the cylinder head (https://www.yourmechanic.com/article/how-to-buy-a-good-quality-cylinder-head). These head bolts hold the cylinder head to the engine block. The head bolts are long bolts that go through the cylinder head and head gasket...

Play in the steering while driving.

If you feel play in your steering wheel this may be caused by a faulty intermediate shaft, loose tie rod ends/ball joints, or a faulty rack and pinion assembly. A good steering system inspection by a professional would be my...

My car jerks when i put it on R/D and also there is a 2 seconds delay when i put it on reverse ( gear takes 2 seconds to engage )

The transmission has electronic controls as does the engine. It's possible there is an electronic issue. A faulty transmission control module can give symptoms like you are experiencing. The brake light switch (https://www.yourmechanic.com/services/brake-light-switch-replacement) can also cause issues. On modern cars,...

A fuse keeps blowing on my 2005 Dodge Dakota and I don't know if it's my wiring or the fuse box itself

Hi there. If there is a fuse that is blowing then that means that you have a short circuit. That can be anyplace in the electrical system which also includes the fuse box. I would need to know which fuse...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com