Showing articles & questions for topic
p0016

It could very well be a timing chain problem (https://www.yourmechanic.com/services/timing-chain-replacement). The P0016 and 17 indicate that the camshaft sensors (https://www.yourmechanic.com/services/camshaft-position-sensor-replacement) are sensing the camshaft in a position that does not logically correspond with the crankshaft. The P0302 (https://www.yourmechanic.com/article/p0302-obd-ii-trouble-code-cylinder-2-misfire-detected-by-jamahl-walker) and P0355...

Changing the Camshaft Position Sensor (CMP) might solve your problem, but probably won't. The P0016 code is saying that the CMP signal is there, but not at the right time. The Camshaft must be timed precisely to the crankshaft and...

Hello. This code can come up for a few different reasons. It may be as simple as low engine oil or a faulty or clogged oil filter or it can be an issue with the variable valve timing system. Most...

The codes P0016 (https://www.yourmechanic.com/article/p0016-obd-ii-trouble-code-camshaft-position-a-camshaft-position-correlation-bank-1-by-jay-safford) and P0017 (https://www.yourmechanic.com/article/p0079-obd-ii-trouble-code-crankshaft-position-camshaft-position-correlation-bank-1-sensor-b-by-jay-safford) are related to the crankshaft location and the camshaft location. Check the camshaft position sensor and see if its plugged in. If the wiring harness is in good shape and the wires are...

Code P0016 (https://www.yourmechanic.com/article/p0016-obd-ii-trouble-code-camshaft-position-a-camshaft-position-correlation-bank-1-by-jay-safford) broadly means that the PCM has detected that the Crankshaft and Camshaft are out of sync. If they are out of sync beyond a specific, threshold number of degrees, the car simply won't start. The cause of...

Hi there. These codes (https://www.yourmechanic.com/article/p0016-obd-ii-trouble-code-camshaft-position-a-camshaft-position-correlation-bank-1-by-jay-safford) lead me to believe that the cam/crank timing is out. However, there are possible underlying problems that can set the same codes and give you the symptoms you're describing. You could have a wiring/connector issue...

Hello. Trouble code P0016 (https://www.yourmechanic.com/article/p0016-obd-ii-trouble-code-camshaft-position-a-camshaft-position-correlation-bank-1-by-jay-safford) is set when the computer detects that there is an issue with the timing between the engine's camshaft and crankshaft signals. The camshaft and crankshafts are connected by a belt or chain, and are precisely...

The OBD-II error code P-0016 (https://www.yourmechanic.com/article/p0016-obd-ii-trouble-code-camshaft-position-a-camshaft-position-correlation-bank-1-by-jay-safford) is a generic code that indicates that the camshaft position sensor (https://www.yourmechanic.com/services/camshaft-position-sensor-replacement) for bank one does not correlate to the signal from the crankshaft position sensor. Some of the common trigger points that create...

The on board diagnostic (OBD) sets a pending code each time the ECU detects a problem. It confirms the code if it sees the same problem twice. So you're really only dealing with the two codes : P0016 and 17.These...

The gap between the 6K and the 7K line is considered the red zone. This zone is marked as the over-revving speed for the engine as the valves cannot shut any faster and the timing chain creates too much slack...

Of course, after a repair be sure to erase the codes. If the same codes do return after erasure, then there is a continuing, unresolved problem. Diagnostic Trouble Code P0016 (https://www.yourmechanic.com/article/p0016-obd-ii-trouble-code-camshaft-position-a-camshaft-position-correlation-bank-1-by-jay-safford) and Diagnostic Trouble Code P0017 (https://www.yourmechanic.com/article/p0079-obd-ii-trouble-code-crankshaft-position-camshaft-position-correlation-bank-1-sensor-b-by-jay-safford) have multiple causes...

Hi...Diagnostic Trouble Code P0016 (https://www.yourmechanic.com/article/p0016-obd-ii-trouble-code-camshaft-position-a-camshaft-position-correlation-bank-1-by-jay-safford) has many causes other than a failed camshaft position sensor. Other possible causes for Code P0016(https://www.yourmechanic.com/article/p0016-obd-ii-trouble-code-camshaft-position-a-camshaft-position-correlation-bank-1-by-jay-safford) to set include: the camshaft timing is wrong because the timing chain jumped teeth; the camshaft phaser is out...

Hi there. The P0016 code (https://www.yourmechanic.com/article/p0016-obd-ii-trouble-code-camshaft-position-a-camshaft-position-correlation-bank-1-by-jay-safford) is a camshaft/crankshaft correlation bank(1) issue. The P000b is camshaft position slow response bank(1) issue. These codes together are an indication that camshaft timing is out of sync with the crankshaft. This problem has...

Hello. If the oil level was low, then it will cause these codes (P0016 (https://www.yourmechanic.com/article/p0016-obd-ii-trouble-code-camshaft-position-a-camshaft-position-correlation-bank-1-by-jay-safford) and P0017 (https://www.yourmechanic.com/article/p0079-obd-ii-trouble-code-crankshaft-position-camshaft-position-correlation-bank-1-sensor-b-by-jay-safford)) to appear. The variable valve timing system on this vehicle is controlled with oil pressure so when the oil level is low...

Hi, from what you’ve described and the nature of the two codes, it sounds like a timing problem. It’s possible that the timing chain has stretched, the timing chain tensioner needs to be replaced, a timing chain guide has slipped...

The crankshaft position sensor is located down on the right side (if you are standing facing the engine from the front of the vehicle) of the motor just to the right of the crankshaft pulley. To remove this, disconnect the...