Showing articles & questions for topic
Compass

Hi Christopher. Thanks for contacting us today. The first question I'd ask is if the stored error codes were cleared after the speed sensor was replaced. If not, it's quite possible that the reason the lights are still on is...

If the check engine light is on, there will be stored trouble codes and those will provide clues to the mechanic as to what is going on. Transmission oil color is not always dispositive of a fault but if the...

Hi Darryl. You might want to watch this video (https://www.youtube.com/watch?v=dfm-goFg-qo) to learn how the UConnect language settings can be changed. Also, refer to your owner manual for additional instructions.

When the compass displays CAL is due to the system lost GPS signal. Try driving the vehicle in an open area and then in a parking lot drive in circles for about 3 times and see if the CAL changes...

You need to first remove the tires again and verify you put the pads in correct with back plate of pads facing out and make sure the thin dust shield is not rubbing the rotors. Also make sure the pad...

ETC pertains to the electronic throttle control system. It is possible that a fault exists in the ETC system and so the first thing to do is check for stored diagnostic trouble codes. Be sure you have a fully charged...

There should be no appreciable run-out on the crank pulley and if a physical inspection of the harmonic balancer reveals damage such as a broken, cracked or separated rubber bond, the balancer should be replaced. If you do have a...

Hello - this is a judgement call. It is common practice, but not a "standard", to replace the thermostat when replacing the water pump. This is mainly due to access to both easily when replacing either one, and the relatively...

The location of the ignition coil for the 3rd cylinder is the 3rd cylinder back from the front of the engine where the belts are. From viewing the engine from the front of the vehicle, the 3rd cylinder will be...

Hi there. Although our mobile mechanics can typically replace steering / suspension components, we are not able to complete suspension alignments. Since it's highly recommended to have this service completed at the same location and before driving the vehicle, I...

Shaking or vibrating may be caused by many different things such as faulty spark plugs, poor fuel pressure or misfires. Other things such as a faulty idle air control valve (https://www.yourmechanic.com/services/idle-control-valve-replacement) may cause the engine idle to drop below the...

Hi Alonna. Thanks for contacting us today. I'm a bit confused with the question. If the seat belt is locked inside the latching mechanism, then it might be possible to unlock the seatbelt by pressing down on the belt and...

The check engine light (https://www.yourmechanic.com/services/check-engine-light-is-on-inspection) indicates that there is likely something wrong with the engine or transmission in your vehicle and will usually come on in conjunction with the vehicle going into the reduced power mode (https://www.yourmechanic.com/services/reduced-power-light-is-on-inspection). This happens when...

The problem sounds like the transmission is not shifting. This can be caused by several possible causes. You will need to have the computer tested for stored codes to see if it points to the transmission or other possible problems....

Hi there. When the check engine light comes on, it's due to a mechanical or electrical fault that is detected by a sensor and triggered by the ECU of the car. If your check engine light is on and the...

Hi There, This is something that usually requires the steering angle sensor (https://www.yourmechanic.com/services/steering-angle-sensor-replacement) to be re-calibrated or replaced. I would suggest having a professional from YourMechanic come to your location to have this done. As you may know, the steering...

There are a number of things that can cause poor fuel mileage. A faulty camshaft position sensor (https://www.yourmechanic.com/services/camshaft-position-sensor-replacement) is one of them. The camshaft position sensor is a magnetic sensor that monitors camshaft speed to regulate ignition timing and fuel...

Hello, thank you for writing in. The vehicle is likely having issues with the battery cables or the ground connection. With that being said, the battery terminals and the cables both need to be clean, dry, and tight. Double check...

Hi There, What you are describing sounds like it may be related to a faulty transmission control module or potentially a bad transmission speed sensor. The speed sensor reads the rotational speed of the reluctor wheel, located within the transmission....

Hi there. If this happened right after the belt was installed then it probably has something to do with that installation. However, there is the possibility of a simple coincidence; things can happen and parts do fail. I would have...